PRO-SERIES MOTORIZED DIAMOND WHEEL BRAKE TRUING DRESSER (3800-5251)

PRO-SERIES MOTORIZED DIAMOND WHEEL BRAKE TRUING DRESSER (3800-5251) (SKU: 3800-5251)

Pro-Series Motorized Diamond Wheel Brake Truing Dresser

• This motorized power dresser is designed for truing the periphery and the face of larger diamond, CBN and superabrasive wheels
• It can be mounted on almost any grinding machine using either a magnetic chuck table
• It can also be mounted with screws to a fixturing device
• Cast Iron and steel
• Very rugged and durable
• For exceptionally good finishes
• Operates at 120 RPM
• Power Supply: 110V/60Hz/ I Phase
• Dimensions are 105″ x 5″x 3.5″
• Net Weight is 13 lbs
• The Power Dresser device is always used dry. Traverse the Power Dresser back and forth at 30 to 60 inches per minute. Downfeed .0005″ to .001″ at the end of each traverse. The truing wheel should run off the diamond wheel after each traverse to avoid chipping the edges of the diamond wheel. During the last few passes, reduce the downfeed to .00025″ per pass.
• When using the Power Dresser truing device, the only movement between the two wheels is traverse. Do not operate the work table on a rotary or reciprocating table traverse surface grinder
• When the truing operation has been completed, there will be a smooth, continuous contact and firing throughout each traverse stroke. Visual inspection of the diamond section will show an even appearance around the wheel. A reading with a dial indicator will show no runout

Specifications

• Pro-Series Motorized Diamond Wheel Brake Truing Dresser
• This motorized power dresser is designed for truing the periphery and the face of larger diamond, CBN and superabrasive wheels.
• It can be mounted on almost any grinding machine using either a magnetic chuck table.
• It can also be mounted with screws to a fixturing device.
• Very rugged and durable cast iron and steel.
• Operates at 120 RPM. Power Supply: 110V/60Hz/ I Phase
• For exceptionally good finishes.
• Dimensions are 105″ x 5″x 3.5″.
• Net Weight is 13 lbs.
• Mount the device with it’s wheel spindle parallel to the spindle of the straight wheel being trued. For cylinder or cup wheels, mount perpendicular to their spindle. The correct wheel specification is determined by the grit size and bond type of the diamond wheel being trued.
• Bring the diamond wheel and the truing wheel together until they almost touch. Turn on the diamond wheel (at normal grinding speed). At the point of contact, bring the two wheels together until they just touch. Be sure that the truing wheel is turning in the same direction as the diamond wheel. Switch on the Power Dresser.
• The Power Dresser device is always used dry. Traverse the Power Dresser back and forth at 30 to 60 inches per minute. Downfeed .0005″ to .001″ at the end of each traverse. The truing wheel should run off the diamond wheel after each traverse to avoid chipping the edges of the diamond wheel. During the last few passes, reduce the downfeed to .00025″ per pass.
• When using the Power Dresser truing device, the only movement between the two wheels is traverse. Do not operate the work table on a rotary or reciprocating table traverse surface grinder.
• When the truing operation has been completed, there will be a smooth, continuous contact and firing throughout each traverse stroke. Visual inspection of the diamond section will show an even appearance around the wheel. A reading with a dial indicator will show no runout.
• Weight: 17
• Dimensions: L 8, W 12, H 8

Benefits

• Industrial-grade tooling designed for dependable shop performance.
• Supports consistent results when applied with correct setup practices.
• A practical choice for U.S. machine shops and maintenance work.

Recommended use

• Confirm compatibility (size, interface, machine capacity) before ordering.
• Follow safe operating practices and use appropriate PPE.
• Optimize setup rigidity and process parameters for best results.

USA Warehouse Stock — Fast U.S. fulfillment.